Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5848 visitantes online.
Productos
Información
Destacado
Inicio >> SHARP >> XVZ9000U Manual de Servicio
 
 0 artículo(s) en Su carrito 

SHARP XVZ9000U
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del SHARP XVZ9000U Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages:

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
XV-Z9000U/E

When the DMD unit has been replaced
Note: DMD chip and Formatter PWB are supplied at the same time, and an exchange only with DMD isn't done.Refer to "REMOVING OF MAJOR PARTS" when exchanging Formatter PWB. There is no need to readjust the back focal distance of the projection lens. If focusing is noticeably poor, however, make this readjustment. (1) (2) (3) (4) (5) (6) (7) Provide a distance of 2.4 m between the set and the screen. Adjust the lens shift until the projection lens comes to the same level as the center of the screen. Detach the optical unit top cover A from behind the projection lens. Loosen the four hex screws B in the back of the projection lens. Adjust the zoom knob at the front of the projection lens to �tele end� and ensure good focusing. Then adjust the zoom knob at the front of the projection lens to �wide end�. Insert the adjustment screwdriver C (9EVDRIVERZ9000) in the hole D at the back of the lens. Put the center of the screen in the best focus. (Preferably feed the SXGA signal for 1-dot white crosshatch pattern or 1-dot white dot pattern on black background.) (8) Move the zoom knob from �wide end� back to �tele end� and see if focusing is ensured. If not, repeat the above steps (5), (6) and (7) until the best focus is achieved. (9) Tighten the four hex screws B to the torque of 0.3 Nm (3.06 kgfcm), and apply screw loctite to them. (10) Attach the optical unit top cover A back into position. Finally fix the two screws E and apply screw loctite to them.
E E

A

C

X

B D

B

B B

Expansion figure of part X

23

Quizás también quiera comprar

$4.99

XV-Z9000U SHARP
Catálogo de piezas

Únicamente Catálogo de Partes. Está disponible en formato PDF. Muy útil si su equipo se ha averi…
>
Parse Time: 0.146 - Number of Queries: 100 - Query Time: 0.036