Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5770 visitantes y 
3 usuarios online.
Productos
Información
Destacado
Inicio >> SHARP >> VLPD5S Manual de Servicio
 
 0 artículo(s) en Su carrito 

SHARP VLPD5S
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del SHARP VLPD5S Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages:

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
VL-PD5S/E

8-3. How to operate with the circuit board without the cassette controller assembly.
In this method, if the procedure is followed incorrectly there is danger of damaging the mechanism and the tape, so except in special cases, such as when measuring the VSR torque, do not perform this procedure. Normally operate this unit with the cassette controller assembly attached. Be sure to follow each caution mentioned. (1) Apply DC3V to the loading motor to set the EJECT mode. (2) Remove the down switch angle. 1) In Fig. 5 remove the screws P and Q . Note) The loading motor solder joint (part T, Fig. 5) of DEW sensor FPC applied to the down switch angle is not removed. After the down switch angle is removed, take care so that the DEW sensor FPC is not broken. (3) Surely secure the moving piece R of down switch as shown in Fig. 6 with the aid of adhesive tape so that the switch is turned on. (4) Install the down switch angle. Note) To set the REC mode, press the pin of recognition switch S (not required in other modes). (5) Set the test mode (T-01) with the adjustment remote controller without loading the tape. Thereby the mechanism operation is enabled with the mode key. (6) To eject, remove the tape (3).
T

P

Q

S

8-4. Phase matching
For the parts listed below, match the phases as shown in Fig. 7. (1) AHC cam (2) MODE switch (3) Main cam (4) Sub cam Note) Before disassembling, check the marker positions carefully. Note) When installing the engagement gear, make sure that the main cam and sub cam phase matching hole aligns with the chassis hole. Note) After phase matching, turn the MODE switch by hand and confirm that it turns almost one complete turn. (After checking, return it to its original position.)

Fig. 5. STANDBY mode

R Down switch moving piece

R Down switch moving piece Down switch angle

Adhesive tape Adhesive tape

AHC cam Phase matching hole (for chassis) Phase matching mark

Fig. 6

MODE switch

Phase matching mark

Main cam

Coupling gear

Sub cam Phase matching hole (for chassis)

Phase matching hole (for chassis)

Fig. 7

15

Quizás también quiera comprar

$4.99

VL-PD5S SHARP
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

VL-PD5S SHARP
Catálogo de piezas

Únicamente Catálogo de Partes. Está disponible en formato PDF. Muy útil si su equipo se ha averi…
>
Parse Time: 0.164 - Number of Queries: 101 - Query Time: 0.037