Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5749 visitantes online.
Productos
Información
Destacado
Inicio >> SHARP >> VLNZ8S Manual de Servicio
 
 0 artículo(s) en Su carrito 

SHARP VLNZ8S
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del SHARP VLNZ8S Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages:

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
VL-NZ10S/H/E

8-3. How to operate with the circuit board without the cassette controller assembly.
In this method, if the procedure is followed incorrectly there is danger of damaging the mechanism and the tape, so except in special cases, such as when measuring the VSR torque, do not perform this procedure. Normally operate this unit with the cassette controller assembly attached. Be sure to follow each caution mentioned.

(1) Apply DC3 ~ 4V to the loading motor to enter the standby mode. (2) Securely press the movable piece L of the down SW with cellophane tape or similar to turn on SW. (Take care that the movable piece turns only in the shown arrow direction.) Note: To enter REC mode, press the pin of the recognition switch M . (Unnecessary in other modes.) (3) Set the test mode (T-01) with the adjustment remote controller without putting the tape, and the mechanical operation will become possible with the mode key. (4) For ejection, remove the tape of (2).
Side view Movable piece of down SW.

Rotary direction of movable piece

8-4. Phase matching

Fig. 7. LOADING START mode

Referring to Figs. 8 and 9, align the phase for the following parts. (1) Eject lever (2) Eject control lever (3) Mode SW (4) Main cam (5) Sub cam Note: Before disassembly, sufficiently check the marker position. Note: When installing the joining gears, verify that the phase matching holes of the main cam and subcam are aligned to the hole of the chassis. Note: After the phase is aligned, turn the mode SW with hand, and verify that it turns nearly one turn. (After verification, return it to the original position.)

Eject control lever Eject lever

Phase matching hole (for chassis) Phase matching hole (for gear) Mode switch Phase matching mark

Fig. 8

Main cam Phase matching hole (for chassis)

Coupling gear

Sub cam Phase matching hole (for chassis)

Fig. 9

15

Quizás también quiera comprar

$4.99

VL-NZ8S SHARP
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …
>
Parse Time: 0.175 - Number of Queries: 99 - Query Time: 0.041