Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5839 visitantes online.
Productos
Información
Destacado
Inicio >> SHARP >> CDC470H Manual de Servicio
 
 0 artículo(s) en Su carrito 

SHARP CDC470H
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del SHARP CDC470H Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages:

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
PREPARATION FOR USE
Notes concerning use:

SETTING THE CLOCK

In this example, clock is set for the 24-hour (0:00) system. ation becomes erratic.
and sensor on the main unit with a soft cloth. Exposing sensor on the main unit to strong light may (8" 20') interfere with operation. Change lighting or the direction

1 Set ON/STAND-BY switch to STAND-BY. Replace the batteries if control distance decreases or oper-

2 Press the CLOCK button. Periodically clean transmitter LED on the remote control
STAND-BY
of the unit. CLOCK
1 Keep the remote control"AM away12:00" from� moisture,The excessive12-hour heat,display 1will 5appear.

3 4

ON/ Within 5 seconds, press the MEMORY/SET button. 0.2 6 m

Press TUNING/TIME ( or ) button to select the time

display mode.

MEMORY/ shock, and vibrations. (AM 12:00 PM 11:59) SET "AM 0:00" � The 12-hour display will appear.
(AM 0:00 PM 11:59)

TUNING/TIME "0:00" � The 24-hour display will appear. ( ) (0:00 23:59)

5 Press the MEMORY/SET button.

2 6 Press TUNING/TIME ( or ) button to adjust the hour. RESETTING THE MICROCOMPUTER

3 ously. To erase all of the stored memory contents (clock and timer
If the display is not correct.

Press TUNING/TIME button once to advance the time by 1 hour. Press for more than 0.5 seconds to advance continuReset microcomputer under the following conditions:

When the 12-hour display is selected, "AM" will change autosettings, tuner and CD presets). matically to "PM".

4 7 Press MEMORY/SET button. If the operation is not correct. 2 8
Note: Press TUNING/TIME ( o r ) button to adjust the

1,2 2 contents of preset memory" on page 19. 1 Press ON/STAND-BY switch to enter the stand-by mode. The hour setting will not even if minutes advance 2 Press VOLUME button, the TUNING/TIME button

12:00 AM 0:00

minutes. To tuner preset memory, see "To erase all of the

5 in 5-minute intervals.

Press button for at least 0.5 seconds to change the time

from "59" to "00".

CD-C470H,C470E,C480H/CP-C470H,C470E,C480H

OPERATION MANUAL

�6�

9 Press the MEMORY/SET button. and ON/STAND-BY switch all at the same time. Hold 6

The clock starts operating from "0" seconds. (Seconds are them down for at least 1 second. not displayed.)

7 Note:

8 flash on and off to indicate time when the power failure

In event of a failure or when the AC power lead is disconnected, the clock display will go out. When AC power supply is restored, the clock display will

occurred or when the AC power lead was disconnected. If this happens, follow procedure below to change the clock time.

9

change clock time: To see time display: (When the power is ON)

When the ON/STAND-BY switch is set to STAND-BY. Press the CLOCK button.

The time display will appear for about 5 seconds. When unit is in the demonstration mode, press

DEMO button to enter the clock mode.

To switch the time display mode:

Press the MEMORY/SET button.

1 2 1 Set the ON/STAND-BY switch to STAND-BY. Perform steps 6 9 above.

2 Press VOLUME button, the TUNING/TIME button

2

When the ON/STAND-BY switch is set to ON. and ON/STAND-BY switch all at the same time. Hold them Press the CLOCK button. down for at least 1 second. Within 5 seconds, press the MEMORY/SET button. Perform steps 6 9 above.

1

Note: The operation explained above will erase all data stored in memory, such as clock timer settings, tuner and CD presets.

3 Perform steps 1 9 above. 3

Quizás también quiera comprar

$4.99

CDC470H SHARP
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …
>
Parse Time: 0.265 - Number of Queries: 100 - Query Time: 0.071