Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5676 visitantes y 
2 usuarios online.
Productos
Información
Destacado
Inicio >> SHARP >> 29R600P Manual de Servicio
 
 0 artículo(s) en Su carrito 

SHARP 29R600P
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del SHARP 29R600P Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages:

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
CONVERGENCE ADJUSTMENT CUT OFF , WHITE BALANCE, SUB BRIGHT, & FOCUS ADJUSTMENT.

NO POINT ADJUSTMENT CONDITION/PROCEDURE WAVEFORM OR OTHERS
2

CONVERGENCE Receive the "CROSSHATCH R G B 1 CRT Cut OFF ADJ. 1. Switch TV to VIDEO MODE, Blue Back: * Before adjustment , make
R

(To be done after the PATTERN" signal. (I C BUS CONTROL) OFF, Without Video Signal. sure that this adjustment purity adjustment.) Using remote controller, call 2. Connect oscilloscope to TP851. with the initial bus data

NORMAL mode. (Use a 10:1 probe) "White Point (G)" & G (Static convergence) Range: 500mV/div "White Point (B)" are 32. B 1. Turn the 4 pole magnet to a proper Sweep Time: 5ms/div opening angle in order to superpose the Press "DC" mode blue and red colours. Figure a 3. Using the remote controller, call 2. Turn the 6 pole magnet to a proper NORMAL mode. opening angle in order to superpose 4. Adjust Screen VR so that the tip of B G R green colour over the blue and red signal reach 2.5Vdc ± 0.1Vdc. Figure 5 colours.
B 2 Balance ADJ. 5. Receive the MONOSCOPE PATTERN *Note : White Point (G) G 2 UP 2 " KEY (I C BUS CONTROL) signal.

(Dynamic convergence) screen in the following steps. 7. Adjust (G)", "White Point White Point (B) a) Fig. a : Drive the wedge at point "a" upward. 1. Adjust convergence on the fringes of 6. Call the "BKGD" in SERVICE mode. UP 3 " KEY (B)" data to have a colour temperature of 12300k (White) *Note.

R

DOWN 5 " KEY

b) Fig. b : Drive the wedge at point "a" R G B UP / DOWN.
G deflection coil downward. *12300k x=272 R c) Fig. c : Drive the "c" wedge deeper

and swing the deflection coil Figure b DOWN 6 " KEY As the above data can be

"b" and swing the B

y=275

and swing the deflection coil (Minolta Colour Analyzer rightward. CA-100) Figure c 3 SUBBRIGHT ADJ. 8. Receive the "CROSSHATCH and swing the deflection coil (I C BUS CONTROL) PATTERN" Signal. 9. Call the "SUB BRI" in SERVICE mode. 10. Adjust the "SUB-BRI" bus data, so that 3. Apply lacquer to the deflection yoke lock screw, magnet unit ( purity 4 pole, 6 1 2 3 4 5

9
Figure d 1500µA. Finally received the Red only and Blue 12. Press P-NORMAL key.
About 100� 6-pole Magnet

d) Fig. d : Drive the "b" wedge deeper

2

leftward.

2. Fix all wedges on the CRT and apply B G R

glass tape over them. R

pole magnets ) and magnet unit lock Figure 6 screw.

No. 2 line inside the window area G will disappear. B Note: Before starting this adjustment, warm up the unit for 30 minutes or longer at a beam current of 1300 ~

only signals to make sure there is no other colours on screen. 4 BEAM CURRENT 11. Receive the "MONOSCOPE PATTERN" Wedge "a" CHECK Signal. 4-pole Magnet 13. Connect the DC Milliammeter between 3.0 mA Range). Figure 3 5 FOCUS ADJ. 1. Receive the "MONOSCOPE PATTERN"
Lacquer signal.

CRT NECK Lacquer TP601 (-) and TP602 (+). (Full Scale:
"b" Wedge "c"

14. Beam current Must be 1400 ± 100µA.

Purity Magnet NECK

2. Using the remote control, call NORMAL Figure 4 3. Adjust FOCUS control so that the shaded

mode.

29R600P

area of screen be in optimal focus.

Figure 7

Quizás también quiera comprar

$4.99

SX-K700 TECHNICS
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

CJ-V51 PIONEER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

SX-PR602 TECHNICS
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EV-S1000E SONY
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

AG7330 PANASONIC
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EVO-9850 VOLUME 1 SONY
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…
>
Parse Time: 0.201 - Number of Queries: 125 - Query Time: 0.054