Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5905 visitantes online.
Productos
Información
Destacado
Inicio >> SHARP >> 21D2X Manual de Servicio
 
 0 artículo(s) en Su carrito 

SHARP 21D2X
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del SHARP 21D2X Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages:

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
21D2-X

ADJUSTMENT PRECAUTIONS: Make sure TV set is in "Normal Condition" before switch to Service Mode for adjustment.

PIF PURITY ADJUSTMENT
beam current to about 700 µA. ( PRESET ) signal,but with no signal input.

No. point Adjusting procedure/conditions Waveform or others

Tuner IFT Get tuner ready to receive CH. E 9 1 PURITY ADJ. 1. Receive GREEN-ONLY signal. Adjust the

Adjust PLL data. 2. Degauss CRT enough with the degausing coil.

2. Connect sweep generator�s output cable 10k 1n60 1000p Note: Follow the Job Instruction Sheet to
Oscilloscope IF OUT

a b
100k 75ohm

tuner antenna. ( RF SWEEP ) adjust the magnetic field.

3. Adjust the sweep generator�s to 80dBuV. Vertoca Bv: +0.030mT (0.30 gauss) 4. Connect the response lead ( use LOW IMPEDHorizontal Bh: +0.020mT (0.20 gauss)

ANCE probe with wave detector ; see Fig.1 ) to (Reference: page6-2) tuner�s IF output terminal. ( This terminal Fig.1 3. Maintain purity magnet at the zero magnetic must have probe alone connected ). field and keep the static convergence roughly E-9 CH

Fig. 4-1

5. Set the RF AGC to 0 6 V no saturation with adjusted.
P C

waveform. 4. Observe the points a, b as shown in Fig. 4-1

6. tuner IF coil obtain waveform as through microscope. Adjust landing to the

shown in Fig. 2. -1.5+/-0.8dB rank requirements. A

5. Orient the raster rotation to 0 eastward.
Fig.2 Note:Be sure to keep tuner cover in position 6. Tighten up the deflection coil screws.

during this adjustment. » Tightening torque: 108 20 N (11 ± 2 kgf) B

7. Make sure CRT corners landing meet the rank requirements. If not, stick the magnet sheet A = B
2 RF-AGC 1. Receive "PAL COLOUR BAR" signal. Note: For the 50 ohm signal

to correct it.

TAKE OVER » Signal Strength: 57 ± 1 dBµV (75 ohm open) strength gauge, when not Note: This adjustment must be done after POINT AD2. Connect the oscilloscope to TP201 (Tuner AGC u s g 0 / 7 5 i m p d a n c e warming up the unit for 30 minutes or Fig. 4-2 JUSTMENT Terminal) as shown in Fig. 3. adapter, signal strength is longer with a beam current over 700 µA. (I C BUS 52±1dBµV(75 ohm open), in(on right of the CRT)2 CONTROL) Oscilloscope stead of 57±1dBµV (75 ohm
Rank "A"

0.1V 138(short) then press factory process Precaution: The loss of using

+ TP201

Note: Set the service mode by JA137 & JA open). colour mode. A * For the following colours press R/C RGB key to
�

8
8-1 8-2

� R/C key change to RGB mono impedance adapter

Bias box TV Set

+

B change. A = B

» Bias box: About 4.5 V Fig. 4-3

Fig. 3

3. Call "AGC" mode in service mode. Adjust the Blue-only Red-only Green-only

4. Change the antenna input signal to 63~67dBµV, (on left of the CRT)

"AGC" bus data to obtain the Tuner output pin drop 0.1V below maximum voltage. Rank "A" and make sure there is no noise. Signal-colour screen cleared

5. Turn up the input signal 90~95 dBµV to be sure * Press R/C RGB key for 1 sec-

that there is no cross modulation beat. ond in NORMAL MODE, the

colour will change to RGB mono colour mode.

Quizás también quiera comprar

$4.99

SX-K700 TECHNICS
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

CJ-V51 PIONEER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

SX-PR602 TECHNICS
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EV-S1000E SONY
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

AG7330 PANASONIC
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EVO-9850 VOLUME 1 SONY
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…
>
Parse Time: 0.302 - Number of Queries: 125 - Query Time: 0.083